HELLO! BOOT0 is starting! boot0 version : 4.0.0 boot0 commit : 4957b8055313f6768659ed788f0a17e34b4c3eec fel_flag = 0x00000000 rtc[0] value = 0x00000000 rtc[1] value = 0x00000000 rtc[2] value = 0x00000000 rtc[3] value = 0x00000000 rtc[4] value = 0x00000000 rtc[5] value = 0x00000000 rtc[6] value = 0x00000000 rtc[7] value = 0x00000000 DRAM DRIVE INFO: V1.3 the chip id is 0x00000081 the chip id is 0x00000081 the chip id is 0x00000081 the chip id is 0x00000081 the chip id is 0x00000081 READ DQS LCDL = 00313132 DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3) DRAM CLK = 432 MHz DRAM zq value: 003b3bfb DRAM dram para1: 10f20200 DRAM dram para2: 00000001 DRAM workmode1: 000009f4 DRAM SIZE =512 M odt delay dram size =512 card boot number = 0 card no is 0 sdcard 0 line count 4 [mmc]: mmc driver ver 2015-04-13 16:07:39 [mmc]: ***Try SD card 0*** [mmc]: SD/MMC Card: 4bit, capacity: 14992MB [mmc]: vendor: Man 00035344 Snr 010c21d0 [mmc]: product: SD16G [mmc]: revision: 3.0 [mmc]: ***SD/MMC 0 init OK!!!*** sdcard 0 init ok The size of uboot is 000e4000. sum=beef20c7 src_sum=beef20c7 Succeed in loading uboot from sdmmc flash. Ready to disable icache. Jump to secend Boot. SUNXI_NORMAL_MODE [ 0.390]e mode U-Boot 2011.09-rc1-00000-g4957b80 (May 23 2017 - 17:38:16) Allwinner Technology [ 0.398]version: 1.1.0 [ 0.401]uboot commit : 4957b8055313f6768659ed788f0a17e34b4c3eec normal mode [ 0.412]pmbus: ready not set main pmu id axp_probe error gpio value=0x20000 [ 0.450]PMU: pll1 1008 Mhz,PLL6=600 Mhz AXI=336 Mhz,AHB=200 Mhz, APB1=100 Mhz sid read already fel key new mode run key detect no key found no key input dram_para_set start dram_para_set end normal mode [ 0.481]DRAM: 512 MiB relocation Offset is: 15af2000 [box standby] read rtc = 0x0 [box_start_os] mag be start_type no use user_gpio config user_gpio ok gic: normal or no secure os mode workmode = 0 MMC: 0 [ 0.565][mmc]: mmc driver ver 2015-04-13 14:50:00 [ 0.570][mmc]: get sdc_phy_wipe fail. [ 0.574][mmc]: get sdc0 sdc_erase fail. [ 0.578][mmc]: get sdc_f_max fail,use default 50000000Hz [ 0.583][mmc]: get sdc_ex_dly_used fail,use default dly [ 0.589][mmc]: SUNXI SD/MMC: 0 [ 0.602][mmc]: *Try SD card 0* [ 0.635][mmc]: CID 0x3534453 0x44313647 0x30010c21 0xd000e333 [ 0.640][mmc]: mmc clk 50000000 [ 0.644][mmc]: SD/MMC Card: 4bit, capacity: 14992MB [ 0.649][mmc]: boot0 capacity: 0KB,boot1 capacity: 0KB [ 0.654][mmc]: ***SD/MMC 0 init OK!!!*** [ 0.659][mmc]: erase_grp_size:0x1WrBlk * 0x200 = 0x200 Byte [ 0.664][mmc]: secure_feature 0x0 [ 0.668][mmc]: secure_removal_type 0x0 [ 0.672]sunxi flash init ok script config pll_de to 864 Mhz Not Found clk pll_video1 in script script config pll_video to 297 Mhz script config pll_periph0 to 600 Mhz DRV_DISP_Init end [disk_read_fs] no the partition error: open tv_vdid.fex, maybe it is not exist [disk_read_fs] no the partition error: open disp_rsl.fex, maybe it is not exist [disk_read_fs] no the partition error: open disp_rsl.fex, maybe it is not exist boot_disp.auto_hpd=1 auto hpd check has 100 times! auto check no any connected, the output_type is 4 [ 1.819]finally, output_type=0x4, output_mode=0x4, screen_id=0x0, disp_para=0x0 try to read logic blk 0 without env partition *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial --------fastboot partitions-------- mbr not exist base bootcmd=run setargs_mmc boot_normal bootcmd set setargs_mmc key 0 cant find rcvy value cant find fstbt value no misc partition is found to be run cmd=run setargs_mmc boot_normal [ 1.867][mmc]: MMC Device 2 not found [ 1.871][mmc]: Can not find mmc dev [ 1.875][mmc]: read first backup failed in fun sdmmc_secure_storage_read line 1854 sunxi_secstorage_read fail get secure storage map err check user data form private the private part isn't exist WORK_MODE_BOOT adver not need show sunxi_bmp_logo_display [ 1.966][mmc]: blkcnt should not be 0 [ 1.980]screen_id =0, screen_width =0, screen_height =0 [ 1.985]frame buffer address 46400036 [ 1.989]Hit any key to stop autoboot: 0 [ 3.668]ready to boot board_display_setenv: disp_para=0 init_disp=20b0404 tv_vdid=0 [ 3.676][mmc]: MMC Device 2 not found [ 3.680][mmc]: mmc not find,so not exit [ 3.684] Starting kernel ... [sun8i_fixup]: From boot, get meminfo: Start: 0x40000000 Size: 512MB ion_carveout reserve: 160m@0 256m@0 130m@1 200m@1 ion_reserve_select: ion chipid [0x2c00081! ion_reserve_common: ion reserve: [0x56000000, 0x60000000]! [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.4.39-h3 (root@wwd) (gcc version 4.6.3 20120201 (prerelease) (crosstool-NG linaro-1.13.1-2012.02-20120222 - Linaro GCC 2012.02) ) #3 SMP PREEMPT Tue May 23 17:37:51 CST 2017 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: sun8i [ 0.000000] cma: CMA: reserved 160 MiB at 56000000 [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] On node 0 totalpages: 131072 [ 0.000000] free_area_init_node: node 0, pgdat c0a5c040, node_mem_map c0b80000 [ 0.000000] Normal zone: 1152 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 129920 pages, LIFO batch:31 [ 0.000000] script_init enter! [ 0.000000] script_init exit! [ 0.000000] PERCPU: Embedded 8 pages/cpu @c12ea000 s11840 r8192 d12736 u32768 [ 0.000000] pcpu-alloc: s11840 r8192 d12736 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129920 [ 0.000000] Kernel command line: console=ttyS0,115200 console=tty0 root=/dev/mmcblk0p2 rootwait storage_type=1 init=/sbin/init loglevel=8 partitions= selinux=0 fsck.repair=yes boot_type=1 disp_para=0 init_disp=20b0404 tv_vdid=0 fb_base=0x46400000 config_size=34796 [ 0.000000] setup_bootdev 1 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] allocated 1048576 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 512MB = 512MB total [ 0.000000] Memory: 339040k/339040k available, 185248k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0955858 (9527 kB) [ 0.000000] .init : 0xc0956000 - 0xc09a9e40 ( 336 kB) [ 0.000000] .data : 0xc09aa000 - 0xc0a5e878 ( 723 kB) [ 0.000000] .bss : 0xc0a5f02c - 0xc0b7fea0 (1156 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] NR_IRQS:544 <6>[ 0.000000] Architected local timer running at 24.00MHz. [ 0.000000] Switching to timer-based delay loop [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console [tty0] enabled [ 0.001428] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.00 BogoMIPS (lpj=24000000) [ 0.001496] pid_max: default: 32768 minimum: 301 [ 0.001877] Mount-cache hash table entries: 512 [ 0.002987] Initializing cgroup subsys cpuacct [ 0.003027] Initializing cgroup subsys memory [ 0.003099] Initializing cgroup subsys devices [ 0.003131] Initializing cgroup subsys freezer [ 0.003163] Initializing cgroup subsys blkio [ 0.003208] Initializing cgroup subsys perf_event [ 0.003290] CPU: Testing write buffer coherency: ok [ 0.003370] ftrace: allocating 25874 entries in 76 pages [ 0.040370] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.040421] [sunxi_smp_prepare_cpus] enter [ 0.040483] Setting up static identity map for 0x406994d8 - 0x40699530 [ 0.041596] CPU1: Booted secondary processor [ 0.041596] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.041739] CPU2: Booted secondary processor [ 0.041739] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.050277] CPU3: Booted secondary processor [ 0.050277] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.050399] Brought up 4 CPUs [ 0.050399] SMP: Total of 4 processors activated (19200.00 BogoMIPS). [ 0.051145] devtmpfs: initialized [ 0.060106] wakeup src cnt is : 2. [ 0.060134] [exstandby]leave extended_standby_enable_wakeup_src : event 0x800000 [ 0.060165] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_map 0x0 [ 0.060198] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_group 0x40 [ 0.060231] [exstandby]leave extended_standby_enable_wakeup_src : event 0x800000 [ 0.060262] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_map 0x8 [ 0.060294] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_group 0x40 [ 0.060327] sunxi pm init [ 0.060478] pinctrl core: initialized pinctrl subsystem [ 0.067323] NET: Registered protocol family 16 [ 0.068569] DMA: preallocated 2048 KiB pool for atomic coherent allocations [ 0.068569] script_sysfs_init success [ 0.068569] sunxi_dump_init success [ 0.068569] gpiochip_add: registered GPIOs 0 to 383 on device: sunxi-pinctrl [ 0.068569] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver [ 0.068569] plat: add adxl34x device [ 0.068569] plat: add bmp085 device [ 0.068569] plat: add ds1307 device [ 0.068569] plat: add pcf8591 device [ 0.068569] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.068569] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.068569] script config pll_video to 297 Mhz [ 0.068569] script config pll_de to 864 Mhz [ 0.068569] script config pll_ve to 402 Mhz [ 0.068569] sunxi_default_clk_init [ 0.068569] try to set pll6ahb1 to 200000000 [ 0.068569] try to set ahb clk source to pll6ahb1 [ 0.068569] set ahb clk source to pll6ahb1 [ 0.068569] try to set ahb1 to 200000000 [ 0.068569] try to set apb1 to 100000000 [ 0.080273] bio: create slab at 0 [ 0.080467] [ARISC] :sunxi-arisc driver v1.04 [ 0.093702] [ARISC] :arisc version: [v0.1.58] [ 0.191612] [ARISC] :sunxi-arisc driver v1.04 startup succeeded [ 0.191751] pwm module init! [ 0.201735] SCSI subsystem initialized [ 0.201735] usbcore: registered new interface driver usbfs [ 0.201735] usbcore: registered new interface driver hub [ 0.201735] usbcore: registered new device driver usb [ 0.201735] Linux media interface: v0.10 [ 0.201735] Linux video capture interface: v2.00 [ 0.201735] Advanced Linux Sound Architecture Driver Version 1.0.25. [ 0.202134] Bluetooth: Core ver 2.16 [ 0.202204] NET: Registered protocol family 31 [ 0.202230] Bluetooth: HCI device and connection manager initialized [ 0.202263] Bluetooth: HCI socket layer initialized [ 0.202289] Bluetooth: L2CAP socket layer initialized [ 0.202325] Bluetooth: SCO socket layer initialized [ 0.202435] Switching to clocksource arch_sys_counter [ 0.214294] FS-Cache: Loaded [ 0.214666] CacheFiles: Loaded [ 0.226819] NET: Registered protocol family 2 [ 0.227154] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.227762] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.228055] TCP bind hash table entries: 16384 (order: 5, 196608 bytes) [ 0.228317] TCP: Hash tables configured (established 16384 bind 16384) [ 0.228345] TCP: reno registered [ 0.228367] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.228407] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.228723] NET: Registered protocol family 1 [ 0.229142] RPC: Registered named UNIX socket transport module. [ 0.229176] RPC: Registered udp transport module. [ 0.229197] RPC: Registered tcp transport module. [ 0.229218] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.229446] Unpacking initramfs... [ 0.416186] Freeing initrd memory: 2908K [ 0.416957] hw perfevents: enabled with ARMv7 Cortex_A7 PMU driver, 5 counters available [ 0.417131] sunxi_reg_init enter [ 0.418008] audit: initializing netlink socket (disabled) [ 0.418086] type=2000 audit(0.410:1): initialized [ 0.419534] VFS: Disk quotas dquot_6.5.2 [ 0.419747] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.420484] NFS: Registering the id_resolver key type [ 0.420901] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.421548] NTFS driver 2.1.30 [Flags: R/W]. [ 0.421897] fuse init (API version 7.18) [ 0.422288] msgmni has been set to 987 [ 0.423804] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 0.423852] io scheduler noop registered [ 0.423874] io scheduler deadline registered [ 0.423948] io scheduler cfq registered (default) [ 0.424449] [DISP]disp_module_init [ 0.424788] cmdline,init_disp=20b0404 [ 0.424842] cmdline,disp=0 [ 0.480063] Console: switching to colour frame buffer device 160x45 [ 0.496480] [DISP]disp_module_init finish [ 0.496852] sw_uart_get_devinfo()1503 - uart0 has no uart_regulator. [ 0.497031] sw_uart_get_devinfo()1503 - uart1 has no uart_regulator. [ 0.497206] sw_uart_get_devinfo()1503 - uart2 has no uart_regulator. [ 0.497380] sw_uart_get_devinfo()1503 - uart3 has no uart_regulator. [ 0.498170] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI [ 0.498344] sw_uart_pm()890 - uart0 clk is already enable [ 0.498502] sw_console_setup()1233 - console setup baud 115200 parity n bits 8, flow n [ 0.594617] console [ttyS0] enabled [ 1.246016] uart1: ttyS1 at MMIO 0x1c28400 (irq = 33) is a SUNXI [ 1.412366] uart2: ttyS2 at MMIO 0x1c28800 (irq = 34) is a SUNXI [ 1.580425] uart3: ttyS3 at MMIO 0x1c28c00 (irq = 35) is a SUNXI [ 1.739582] sunxi_cmatest_init enter [ 1.902922] sunxi_cmatest_init success [ 2.075039] [drm] Initialized drm 1.1.0 20060810 [ 2.166608] loop: module loaded [ 2.174688] sunxi_spi_chan_cfg()1383 - [spi-0] has no spi_regulator. [ 2.186114] sunxi_spi_chan_cfg()1383 - [spi-1] has no spi_regulator. [ 2.198077] spi spi0: master is unqueued, this is deprecated [ 2.208974] tun: Universal TUN/TAP device driver, 1.6 [ 2.218846] tun: (C) 1999-2004 Max Krasnyansky [ 2.231018] PPP generic driver version 2.4.2 [ 2.240362] PPP BSD Compression module registered [ 2.249951] PPP Deflate Compression module registered [ 2.262815] PPP MPPE Compression module registered [ 2.272571] NET: Registered protocol family 24 [ 2.281839] PPTP driver version 0.8.5 [ 2.290366] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.322041] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.335384] sunxi-ehci sunxi-ehci.1: new USB bus registered, assigned bus number 1 [ 2.348877] sunxi-ehci sunxi-ehci.1: irq 104, io mem 0xf1c1a000 [ 2.370037] sunxi-ehci sunxi-ehci.1: USB 0.0 started, EHCI 1.00 [ 2.381617] hub 1-0:1.0: USB hub found [ 2.390036] hub 1-0:1.0: 1 port detected [ 2.418970] sunxi-ehci sunxi-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.432220] sunxi-ehci sunxi-ehci.2: new USB bus registered, assigned bus number 2 [ 2.445505] sunxi-ehci sunxi-ehci.2: irq 106, io mem 0xf1c1b000 [ 2.470043] sunxi-ehci sunxi-ehci.2: USB 0.0 started, EHCI 1.00 [ 2.481455] hub 2-0:1.0: USB hub found [ 2.489836] hub 2-0:1.0: 1 port detected [ 2.518869] sunxi-ehci sunxi-ehci.3: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.532178] sunxi-ehci sunxi-ehci.3: new USB bus registered, assigned bus number 3 [ 2.545526] sunxi-ehci sunxi-ehci.3: irq 108, io mem 0xf1c1c000 [ 2.570043] sunxi-ehci sunxi-ehci.3: USB 0.0 started, EHCI 1.00 [ 2.581535] hub 3-0:1.0: USB hub found [ 2.590091] hub 3-0:1.0: 1 port detected [ 2.619046] sunxi-ehci sunxi-ehci.4: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.632456] sunxi-ehci sunxi-ehci.4: new USB bus registered, assigned bus number 4 [ 2.645939] sunxi-ehci sunxi-ehci.4: irq 110, io mem 0xf1c1d000 [ 2.670040] sunxi-ehci sunxi-ehci.4: USB 0.0 started, EHCI 1.00 [ 2.681697] hub 4-0:1.0: USB hub found [ 2.690438] hub 4-0:1.0: 1 port detected [ 2.699569] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.730937] sunxi-ohci sunxi-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 2.743973] sunxi-ohci sunxi-ohci.1: new USB bus registered, assigned bus number 5 [ 2.756985] sunxi-ohci sunxi-ohci.1: irq 105, io mem 0xf1c1a400 [ 2.824594] hub 5-0:1.0: USB hub found [ 2.833333] hub 5-0:1.0: 1 port detected [ 2.862642] sunxi-ohci sunxi-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 2.875892] sunxi-ohci sunxi-ohci.2: new USB bus registered, assigned bus number 6 [ 2.889060] sunxi-ohci sunxi-ohci.2: irq 107, io mem 0xf1c1b400 [ 2.964575] hub 6-0:1.0: USB hub found [ 2.973478] hub 6-0:1.0: 1 port detected [ 3.002861] sunxi-ohci sunxi-ohci.3: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 3.016179] sunxi-ohci sunxi-ohci.3: new USB bus registered, assigned bus number 7 [ 3.029395] sunxi-ohci sunxi-ohci.3: irq 109, io mem 0xf1c1c400 [ 3.104613] hub 7-0:1.0: USB hub found [ 3.113511] hub 7-0:1.0: 1 port detected [ 3.142922] sunxi-ohci sunxi-ohci.4: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 3.156259] sunxi-ohci sunxi-ohci.4: new USB bus registered, assigned bus number 8 [ 3.169520] sunxi-ohci sunxi-ohci.4: irq 111, io mem 0xf1c1d400 [ 3.244585] hub 8-0:1.0: USB hub found [ 3.253506] hub 8-0:1.0: 1 port detected [ 3.262914] Initializing USB Mass Storage driver... [ 3.273203] usbcore: registered new interface driver usb-storage [ 3.284545] USB Mass Storage support registered. [ 3.294433] usbcore: registered new interface driver ums-alauda [ 3.305784] usbcore: registered new interface driver ums-cypress [ 3.317219] usbcore: registered new interface driver ums-datafab [ 3.328520] usbcore: registered new interface driver ums_eneub6250 [ 3.339947] usbcore: registered new interface driver ums-freecom [ 3.351109] usbcore: registered new interface driver ums-isd200 [ 3.362192] usbcore: registered new interface driver ums-jumpshot [ 3.373350] usbcore: registered new interface driver ums-karma [ 3.384197] usbcore: registered new interface driver ums-onetouch [ 3.395222] usbcore: registered new interface driver ums-realtek [ 3.406056] usbcore: registered new interface driver ums-sddr09 [ 3.416722] usbcore: registered new interface driver ums-sddr55 [ 3.427346] usbcore: registered new interface driver ums-usbat [ 3.437866] usbcore: registered new interface driver usbserial [ 3.448241] usbserial: USB Serial Driver core [ 3.456950] usbcore: registered new interface driver option [ 3.466994] USB Serial support registered for GSM modem (1-port) [ 3.478150] file system registered [ 3.487471] android_usb gadget: Mass Storage Function, version: 2009/09/11 [ 3.499082] android_usb gadget: Number of LUNs=3 [ 3.508144] lun0: LUN: removable file: (no medium) [ 3.517473] lun1: LUN: removable file: (no medium) [ 3.526663] lun2: LUN: removable file: (no medium) [ 3.536112] android_usb gadget: android_usb ready [ 3.545253] uinput result 0 , vmouse_init [ 3.554201] mousedev: PS/2 mouse device common for all mice [ 3.565199] ls_fetch_sysconfig_para: ls_unused. [ 3.574015] ltr_init: ls_fetch_sysconfig_para err. [ 3.583290] [RTC] WARNING: Rtc time will be wrong!! [ 3.592358] [RTC] WARNING: use *internal OSC* as clock source [ 3.602640] sunxi-rtc sunxi-rtc: rtc core: registered sunxi-rtc as rtc0 [ 3.613781] i2c /dev entries driver [ 3.621732] IR RC5(x) protocol handler initialized [ 3.631181] sunxi tsc version 0.1 [ 3.638593] tscdev_init: tsc driver is disabled [ 3.647358] sunxi cedar version 0.1 [ 3.654980] [cedar]: install start!!! [ 3.662813] [cedar]: install end!!! [ 3.670180] Driver for 1-wire Dallas network protocol. [ 3.679465] sunxi_wdt_init_module: sunxi WatchDog Timer Driver v1.0 [ 3.690150] sunxi_wdt_probe: devm_ioremap return wdt_reg 0xf1c20ca0, res->start 0x01c20ca0, res->end 0x01c20cbf [ 3.701583] sunxi_wdt_probe: initialized (g_timeout=16s, g_nowayout=0) [ 3.716303] wdt_enable, write reg 0xf1c20cb8 val 0x00000000 [ 3.726238] timeout_to_interv, line 167 [ 3.734190] interv_to_timeout, line 189 [ 3.742084] wdt_set_tmout, write 0x000000b0 to mode reg 0xf1c20cb8, actual timeout 16 sec [ 3.755235] device-mapper: uevent: version 1.0.3 [ 3.764566] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com [ 3.778109] Bluetooth: HCI UART driver ver 2.2 [ 3.787202] Bluetooth: HCI H4 protocol initialized [ 3.796711] Bluetooth: HCI BCSP protocol initialized [ 3.806447] Bluetooth: HCILL protocol initialized [ 3.815934] Bluetooth: HCIATH3K protocol initialized [ 3.825849] Bluetooth: MSM Sleep Mode Driver Ver 1.2 [ 3.835750] Bluetooth: init no bt used in configuration [ 3.835756] [ 3.852078] calibrat: max_cpufreq 1200Mhz Type 0! [ 3.861816] [cpu_freq] ERR:get cpu extremity frequency from sysconfig failed, use max_freq [ 3.876065] [mmc]: SD/MMC/SDIO Host Controller Driver(v1.111 2015-4-13 15:24) Compiled in May 23 2017 at 10:28:18 [ 3.892397] [mmc]: get mmc0's sdc_power is null! [ 3.902383] [mmc]: MMC host used card: 0x1, boot card: 0x1, io_card 0 [ 3.916576] no red_led, ignore it! [ 3.918030] [mmc]: sdc0 power_supply is null [ 3.934990] Registered led device: green_led [ 3.943874] Registered led device: blue_led [ 3.954026] usbcore: registered new interface driver usbhid [ 3.964324] usbhid: USB HID core driver [ 3.973409] pcm5102a_probe [ 3.984082] asoc: pcm5102a-hifi <-> pri_dai mapping ok [ 3.998698] asoc: sndhdmi <-> sunxi-hdmiaudio.0 mapping ok [ 4.009998] oprofile: using arm/armv7-ca7 [ 4.018757] u32 classifier [ 4.025839] Actions configured [ 4.033654] Netfilter messages via NETLINK v0.30. [ 4.043135] nf_conntrack version 0.5.0 (7902 buckets, 31608 max) [ 4.054398] ctnetlink v0.93: registering with nfnetlink. [ 4.064432] NF_TPROXY: Transparent proxy support initialized, version 4.1.0 [ 4.076295] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. [ 4.087235] xt_time: kernel timezone is -0000 [ 4.096376] IPv4 over IPv4 tunneling driver [ 4.105441] mmc0: new high speed SDHC card at address 0007 [ 4.105692] gre: GRE over IPv4 demultiplexor driver [ 4.105701] ip_gre: GRE over IPv4 tunneling driver [ 4.106380] ip_tables: (C) 2000-2006 Netfilter Core Team [ 4.106613] arp_tables: (C) 2002 David S. Miller [ 4.106686] TCP: cubic registered [ 4.106694] Initializing XFRM netlink socket [ 4.170474] NET: Registered protocol family 10 [ 4.179498] mmcblk0: mmc0:0007 SD16G 14.6 GiB [ 4.189288] Mobile IPv6 [ 4.195996] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 4.196034] mmcblk0: p1 p2 [ 4.212941] IPv6 over IPv4 tunneling driver [ 4.222404] NET: Registered protocol family 17 [ 4.231151] NET: Registered protocol family 15 [ 4.240000] Bluetooth: RFCOMM TTY layer initialized [ 4.249183] Bluetooth: RFCOMM socket layer initialized [ 4.258619] Bluetooth: RFCOMM ver 1.11 [ 4.266478] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 4.276111] Bluetooth: BNEP filters: protocol multicast [ 4.285621] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 4.296098] L2TP core driver, V2.0 [ 4.303527] PPPoL2TP kernel driver, V2.0 [ 4.311403] L2TP IP encapsulation support (L2TPv3) [ 4.320271] L2TP netlink interface [ 4.327477] L2TP ethernet pseudowire support (L2TPv3) [ 4.336482] Registering the dns_resolver key type [ 4.345721] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 4.357781] ThumbEE CPU extension supported. [ 4.366093] Registering SWP/SWPB emulation handler [ 4.376457] sunxi-rtc sunxi-rtc: setting system clock to 1970-01-01 00:01:00 UTC (60) [ 4.388867] ths_fetch_sysconfig_para: type err device_used = 1. [ 4.400736] CPU Budget:Register notifier [ 4.408778] CPU Budget:register Success [ 4.416663] sunxi-budget-cooling sunxi-budget-cooling: Cooling device registered: thermal-budget-0 [ 4.433456] [rf_pm]: module power0 name vcc-wifi-33 [ 4.442758] [rf_pm]: Did not config module_power1 in sys_config [ 4.453182] [rf_pm]: Did not config module_power2 in sys_config [ 4.463540] [rf_pm]: Did not config module_power3 in sys_config [ 4.473822] [rf_pm]: mod has no chip_en gpio [ 4.482220] [rf_pm]: failed to fetch lpo_use_apclk [ 4.491204] [rf_pm]: regulator on. [ 4.498508] [wifi_pm]: no wifi used in configuration [ 4.507603] [rfkill]: init no bt used in configuration [ 4.516882] ALSA device list: [ 4.523693] #0: Pcm5102a [ 4.530166] #1: sndhdmi [ 4.536849] Freeing init memory: 332K [ 5.695964] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 6.688601] mmcblk0: p1 p2 [ 16.235339] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 18.174774] systemd[1]: System time before build time, advancing clock. [ 18.730503] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 18.771708] systemd[1]: Detected architecture arm. [ 18.826984] systemd[1]: Set hostname to . [ 19.195585] systemd[1]: Reached target Swap. [ 19.210209] systemd[1]: Listening on Journal Audit Socket. [ 19.225417] systemd[1]: Listening on udev Kernel Socket. [ 19.240817] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 19.259268] systemd[1]: Listening on udev Control Socket. [ 19.275113] systemd[1]: Created slice User and Session Slice. [ 19.290989] systemd[1]: Reached target Remote File Systems (Pre). [ 19.307375] systemd[1]: Listening on Journal Socket (/dev/log). [ 19.323461] systemd[1]: Reached target Encrypted Volumes. [ 19.338989] systemd[1]: Created slice System Slice. [ 19.353760] systemd[1]: Reached target Slices. [ 19.368232] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ 19.385849] systemd[1]: Listening on Journal Socket. [ 19.511095] systemd[1]: Starting Set console keymap... [ 19.690759] systemd[1]: Starting Remount Root and Kernel File Systems... [ 19.810347] systemd[1]: Mounting Debug File System... [ 19.930681] systemd[1]: Starting Create list of required static device nodes for the current kernel... [ 20.110673] systemd[1]: Starting Load Kernel Modules... [ 20.139580] systemd[1]: Reached target Remote File Systems. [ 20.250748] systemd[1]: Starting Journal Service... [ 20.268663] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 20.289501] systemd[1]: Reached target Paths. [ 20.307493] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 20.423426] systemd[1]: Mounted Debug File System. [ 20.600154] systemd[1]: Started Set console keymap. [ 20.740158] systemd[1]: Started Remount Root and Kernel File Systems. [ 20.880122] systemd[1]: Started Create list of required static device nodes for the current kernel. [ 21.020300] systemd[1]: Started Load Kernel Modules. [ 21.053637] systemd[1]: Started Journal Service. Ubuntu 16.04.2 LTS NanoPi-NEO ttyS0 Default Login: Username = pi Password = pi NanoPi-NEO login: pi (automatic login) _____ _ _ _ _____ _ _____ ____ | ___| __(_) ___ _ __ __| | |_ _| ____| | | ____/ ___| | |_ | '__| |/ _ \ '_ \ / _` | | | | | _| | | | _|| | | _|| | | | __/ | | | (_| | | |_| | |___| |___| |__| |___ |_| |_| |_|\___|_| |_|\__,_|_|\__, |_____|_____|_____\____| |___/ Welcome to Ubuntu 16.04.2 LTS 3.4.39-h3 System load: 1.41 Up time: 35 sec Memory usage: 8 % of 494Mb IP: CPU temp: 35°C Usage of /: 9% of 15G * Documentation: http://wiki.friendlyarm.com/ * Forum: http://www.friendlyarm.com/Forum/ pi@NanoPi-NEO:~$